Recycled Nylon 6 Pellets Polyamide 6 Resin Containing Mineral And Glass Fiber Pa 6 Plastics Raw Materials

Form

Resin Pellets

Filler

Glass Fiber

Mineral

Feature

Thermally Conductive

Non-Chlorinated

Outdoor

Electrically Isolative

Non-Brominated & Non- Chlorinated Flame  Retardant

Usage：                Industria            

          Electrical

 Building and Construction

Physical

Nominal Value

Test Method

Mold Shrinkage, Flow(24 hrs)

0.45 %

ISO 294

Mold Shrinkage, XFlow(24 hrs)

0.65 %

ISO 294

Density / Specific Gravity

1.74 g/cm³

ISO 1183

Water Absorption(24 hrs;23 °C)

0.36 %

ISO 62-1

Mechanical

Nominal Value

Test Method

Izod Impact, Unnotched(80*10*4;23 °C)

25 kJ/m²

ISO 180/1U

Izod Impact, Notched(80*10*4;23 °C)

3 kJ/m²

ISO 180/1A

Tensile Stress, Break(5 mm/min)

105 MPa

ISO 527

Tensile Strain, Break(5 mm/min)

1.7 %

ISO 527

Tensile Modulus(1 mm/min)

1.2E+04 MPa

ISO 527

Flexural Stress, Yield(2 mm/min)

170 MPa

ISO 178

Flexural Modulus(2 mm/min)

1.1E+04 MPa

ISO 178

Thermal

Nominal Value

Test Method

UL Recognized(≥ 1 mm)

V-0

UL 94

Glow Wire Ignition Temperature [GWIT]

1 mm

1.5 mm

1.6 mm

3 mm

800 °C

775 °C

775 °C

800 °C

IEC 60695-2-13

Heat Deflection Temperature[HDT](0.45 MPa;3.2 mm)

209 °C

ASTM D648

CTE, Flow

-40 - 40 °C

-30°C to 80°C

23°C to 80°C

3.1E-05 1/°C

3.5e-05 1/°C

3.7E-05 1/°C

ASTM E831

ISO 11359-2

ISO 11359-2

CTE, XFlow

-40 - 40 °C

-30°C to 80°C

23°C to 80°C

4.8E-05 1/°C

6.0E-05 1/°C

7.3e-05 1/°C

ASTM E831

ISO 11359-2

ISO 11359-2

Thermal conductivity through plane

60*60*3mm plaque

?80*3mm discs

0.8 W/m-K

1.1 W/m-K

ISO 22007-2

Thermal conductivity in plane

60*60*3mm plaque

?80*3mm discs

1.5 W/m-K

1.3 W/m-K

ISO 22007-2

Ball Pressure Test

125°C +/- 2°C

165°C +/- 2°C

PASSES

PASSES

IEC 60695-10-2

Vicat Softening Temperature(Rate B/120)

205 °C

ISO 306

HDT/Bf(0.45)

208 °C

ISO 75/Bf

HDT/Af(1.8)

185 °C

ISO 75/Af

Relative Temp Index, Elec

120 °C

UL 746B

Relative Temp Index, Mechanical with Impact

110 °C

UL 746B

Relative Temp Index, Mechanical without Impact

130 °C

UL 746B

Surface Resistivity

1.0E+16 ohms

ASTM D257

Dielectric Strength, in Oil(1.6 mm)

15.9 kV/mm

ASTM D149

Comparative Tracking Index, CTI

PLC 0

UL 746A

Comparative Tracking Index

600 V

IEC 60112

Hot-wire Ignition, HWI( ≥ 1 mm)

PLC 0

UL 746A

High Amp Arc Ignition, HAI( ≥ 1 mm)

PLC 0

UL 746A

Processing

Nominal Value

Drying Temperature<Injection>

80 °C

Drying Time<Injection>

4 hrs

Maximum Moisture Content<Injection>

0.15 - 0.25 %

Melt Temperature<Injection>

270 - 295 °C

Front, Zone 3 Temperature<Injection>

270 - 290 °C

Middle, Zone 2 Temperature<Injection>

270 - 290 °C

Rear, Zone 1 Temperature<Injection>

260 - 275 °C

Mold Temperature<Injection>

85 - 100 °C

Back Pressure<Injection>

0.2 - 0.3 MPa

Screw Speed <Injection>

20 - 60 rpm