Plastic Raw Material ABS Particles Virgin Regenerated ABS/PC Particles

Form

 Resin Pellets

Feature

Chemical Resistant

Non-Brominated & Non- Chlorinated Flame retardant

Excellent Processability

Non-Chlorinated

 Hydrolysis Resistance

 Thin Wall

Uses

 Consumer

 Electrical

 Medical Device                                   Healthcare

 Building and Construction

Physical

Nominal Value

Test Method

Density / Specific Gravity

1.19

1.2 g/cm³

ASTM D792

ISO 1183

Melt Flow Rate[MFR](260 °C;2.16 kgf)

18 g/10min

ASTM D1238

Water Absorption(23 °C;saturated)

0.2 %

ISO 62-1

Moisture Absorption(50% RH;23 °C)

0.1 %

ISO 62

Melt Volume Rate, MVR(2.16 kg;MVR at 260 °C)

15 cm³/10 min

ISO 1133

Izod Impact, Notched

23 °C

-30 °C

700 J/m

175 J/m

ASTM D256

Instrumented Dart Impact, Total Energy(23 °C)

65 J

ASTM D3763

Notched Izod Impact Strength

notched;80*10*3;23 °C 0

notched;80*10*3;-30 °C 0

40 kJ/m²

10 kJ/m²

ISO 180/1A

C harpy Impact, V-Notched

23 °C;Edgew;80*10*3;sp =62mm 0

-30 °C;Edgew;80*10*3;sp =62mm 0

40 kJ/m²

10 kJ/m²

ISO 179 1eA

Tensile Stress, Yield

50 mm/min;Type I

65 MPa

ASTM D638

50 mm/min

65 MPa

ISO 527

Tensile Stress, Break

50 mm/min;Type I

58 MPa

ASTM D638

50 mm/min

50 MPa

ISO 527

Tensile Strain, Yield

50 mm/min;Type I

4.1 %

ASTM D638

50 mm/min

4 %

ISO 527

Tensile Strain, Break

50 mm/min;Type I

100 %

ASTM D638

50 mm/min

90 %

ISO 527

Tensile Modulus

5 mm/min

2600 MPa

ASTM D638

1 mm/min

2600 MPa

ISO 527

Flexural Stress, Yield

1.3 mm/min;50 mm;span

104 MPa

ASTM D790

2 mm/min

96 MPa

ISO 178

Flexural Modulus

1.3 mm/min;50 mm;span

2500 MPa

ASTM D790

2 mm/min

2500 MPa

ISO 178

UL Recognized

≥ 3 mm

≥ 1.5 mm

≥ 0.75 mm

5VA

5VB

V-0

UL 94

Glow Wire Ignition Temperature [GWIT](3 mm)

800 °C

IEC 60695-2-13

Glow Wire Flammability Index(3 mm)

960 °C

IEC 60695-2-12

Vicat Softening Temperature

Rate B/50

110 °C

ASTM D1525

Rate B/50

110 °C

ISO 306

Rate B/120

113 °C

ISO 306

Heat Deflection Temperature[HDT], Unannealed(3.2 mm;1.82 MPa)

89 °C

ASTM D648

CTE, Flow

-40 - 40 °C

7.5e-05 1/°C

ASTM E831

-40 - 40 °C

7.5e-05 1/°C

ISO 11359-2

CTE, XFlow

-40 - 40 °C

7.5e-05 1/°C

ASTM E831

-40 - 40 °C

7.5e-05 1/°C

ISO 11359-2

Ball Pressure Test(75°C +/- 2°C)

Pass

IEC 60695-10-2

HDT/Af(1.8)

93 °C

ISO 75/Af

Relative Temp Index, Elec

90 °C

UL 746B

Relative Temp Index, Mechanical with Impact

90 °C

UL 746B

Relative Temp Index, Mechanical without Impact

90 °C

UL 746B

Volume Resistivity

> 1E+15 ohms ·cm

IEC 60093

Surface Resistivity, ROA

> 1.E+15 ohms

IEC 60093

Dielectric Strength, in Oil

0.8 mm

1.6 mm

3.2 mm

35 kV/mm

25 kV/mm

17 kV/mm

IEC 60243-1

Comparative Tracking Index, CTI

PLC 3

UL 746A

Hot-wire Ignition, HWI(0.75 mm)

PLC 3

UL 746A

High Amp Arc Ignition, HAI(0.75 mm)

PLC 0

UL 746A

High Voltage Arc Tracking Rate, HVTR

PLC 2

UL 746A

Arc Resistance, Tungsten Electrode

PLC 6

ASTM D495

Processing

Nominal Value

Drying Temperature<Injection>

80 - 90 °C

Drying Time<Injection>

2 - 4 hrs

Maximum Moisture Content<Injection>

0.02 %

Melt Temperature<Injection>

250 - 300 °C

Nozzle Temperature<Injection>

250 - 300 °C

Front, Zone 3 Temperature<Injection>

250 - 300 °C

Middle, Zone 2 Temperature<Injection>

240 - 290 °C

Rear, Zone 1 Temperature<Injection>

230 - 280 °C

Hopper Temperature<Injection>

60 - 80 °C

Mold Temperature<Injection>

60 - 85 °C

Vent Depth <Injection>

0.03 - 0.075 mm