Nylon 6 Resin Containing Thermal Fillers,Enhanced Super Tough Wear PA 6 Pellets Nylon 6 Resin Granule

Form

 Resin Pellets

Feature

Thermally Conductive

Non-Brominated & Non- Chlorinated Flame

 Retardant

Non-Chlorinated

Electrically Isolative

Usage

 Consumer                        Industria

 Building and Construction

 Electrical

Physical

Nominal Value

Test Method

Mold Shrinkage, Flow

24 hrs

0.55 %

ASTM D955

24 hrs

0.55 %

ISO 294

Mold Shrinkage, XFlow

24 hrs

0.65 %

ASTM D955

24 hrs

0.65 %

ISO 294

Density / Specific Gravity

1.68 g/cm³

ISO 1183

Water Absorption(24 hrs;23 °C)

0.23 %

ISO 62-1

Izod Impact, Unnotched

23 °C

152 J/m

ASTM D4812

80*10*4;23 °C

9 kJ/m²

ISO 180/1U

Izod Impact, Notched

23 °C

15 J/m

ASTM D256

80*10*4;23 °C

3 kJ/m²

ISO 180/1A

Tensile Stress, Yield(5 mm/min;Type I)

68 MPa

ASTM D638

Tensile Strain, Break

5 mm/min;Type I

1.2 %

ASTM D638

5 mm/min

1.1 %

ISO 527

Tensile Modulus

5 mm/min

1.0E+04 MPa

ASTM D638

1 mm/min

1.3E+04 MPa

ISO 527

Flexural Stress, break(1.3 mm/min;50 mm;span)

119 MPa

ASTM D790

Flexural Modulus

1.3 mm/min;50 mm;span

1.2E+04 MPa

ASTM D790

2 mm/min

1.2E+04 MPa

ISO 178

Tensile Stress, Break(5 mm/min)

75 MPa

ISO 527

Flexural Stress, Yield(2 mm/min)

105 MPa

ISO 178

UL Recognized(≥ 0.8 mm)                                                   V-0

UL 94

Glow Wire Ignition Temperature [GWIT]

0.8 mm

1.6 mm

3 mm

750 °C

775 °C

800 °C

IEC 60695-2-13

Glow Wire Flammability Index

0.8 mm

1.6 mm

3 mm

960 °C

960 °C

960 °C

IEC 60695-2-12

Heat Deflection Temperature[HDT](0.45 MPa;3.2 mm)     203 °C

ASTM D648

Heat Deflection Temperature[HDT], Unannealed(3.2 mm;1.82 MPa)

137 °C

ASTM D648

CTE, Flow

-40 - 40 °C

-30°C to 80°C

3.3E-05

3.9E-05

1/°C

1/°C

ASTM E831

ISO 11359-2

CTE, XFlow

-40 - 40 °C

-30°C to 80°C

4.4E-05 1/°C

5.5e-05 1/°C

ASTM E831

ISO 11359-2

Thermal conductivity through plane(60*60*3mm plaque) 1.2 W/m-K

ISO 22007-2

Thermal conductivity in plane(60*60*3mm plaque)          5.5 W/m-K

ISO 22007-2

Ball Pressure Test(165°C +/- 2°C)                                        PASSES

IEC 60695-10-2

HDT/Bf(0.45)                                                                       203 °C

ISO 75/Bf

HDT/Af(1.8)                                                                           160 °C

ISO 75/Af

Relative Temp Index, Elec                                                    130 °C

UL 746B

Relative Temp Index, Mechanical with Impact                   100 °C

UL 746B

Relative Temp Index, Mechanical without Impact              130 °C

UL 746B

Surface Resistivity

4.0E+14 ohms

ASTM D257

Dielectric Strength, in Oil(1.6 mm)

7.2 kV/mm

ASTM D149

Dielectric Strength(1.6 mm)

6.1 kV/mm

IEC 60243-1

Comparative Tracking Index, CTI

PLC 0

UL 746A

Comparative Tracking Index

600 V

IEC 60112

Hot-wire Ignition, HWI( ≥ 0.8 mm)

PLC 0

UL 746A

High Amp Arc Ignition, HAI( ≥ 0.8 mm)

PLC 0

UL 746A

Processing

Nominal Value

Drying Temperature<Injection>

80 °C

Drying Time<Injection>

4 hrs

Maximum Moisture Content<Injection>

0.25 %

Minimum Moisture Content<Injection>

0.15 %

Melt Temperature<Injection>

270 - 295 °C

Front, Zone 3 Temperature<Injection>

270 - 290 °C

Middle, Zone 2 Temperature<Injection>

270 - 290 °C

Rear, Zone 1 Temperature<Injection>

260 - 275 °C

Mold Temperature<Injection>

85 - 100 °C

Back Pressure<Injection>

0.2 - 0.3 MPa

Screw Speed <Injection>

20 - 60 rpm